fbpx

CAS/CS Series

CAS/CS Series

DPDT 2 Amp
Features

  • Sensitive type and standard type are available
  • Fully sealed
hasco Recovered

Description

Contact Ratings

Contact Arrangement 2C
Contact Resistance 50mΩ(0.1A 6VDC)
Contact Material Silver Alloy, Gold Flash
Contact Rating(Resistive) 2A/30VDC
2.5A/12VDC
0.5A/125VAC
0.6A/120VAC
Max. Switching Voltage 150VAC/125VDC
Max. Switching Current 2A
Max. Switching Power 75VA/60W
Mechanical Life 1×108 operations
Electrical Life 1×105 operations

Ordering Information

cas 2 1

Characteristics

Insulation Resistance 1000MΩ (at 500VDC)
Dielectric Strength Between coil & contacts 1000VAC  1min
Between open contacts 1000VAC 1min
Operate time (at nomi. volt.) ≤7ms
Release time (at nomi. volt.) ≤5ms
Humidity 98% RH, 40°C
Ambient temperature -25°C ~ +85°C
Shock Resistance Functional 100m/s2
Destructive 980m/s2
Vibration resistance 10Hz ~ 55Hz  1.5mm DA
Unit weight Approx. 5g
Construction Sealed Type

Notes:
1) The data shown above are initial values.
2) Please find coil temperature curve in the characteristic curved below.

Coil Data at 20°C

Standard Type
Nominal
Voltage
VDC
Pick-up
Voltage
(Max.)
VDC
Drop-out
Voltage
(Min.)
VDC
Max.
Allowable
Voltage
VDC
Coil
Resistance
Ω±10%
5 3.5 0.5 7.0 45
6 4.2 0.6 8.4 66
9 6.3 0.9 12.3 140
12 8.4 1.2 17.4 280
24 16.8 2.4 34.0 1070
48 33.6 4.8 64.9 3900
Sensitive Type
Nominal
Voltage
VDC
Pick-up
Voltage
(Max.)
VDC
Drop-out
Voltage
(Min.)
VDC
Max.
Allowable
Voltage
VDC
Coil
Resistance
Ω±10%
5 3.5 0.25 12.5 167
6 4.2 0.30 15.0 240
9 6.3 0.45 22.5 540
12 8.4 0.60 30.0 960
18 12.6 0.90 40.0 1620
24 16.8 1.20 52.9 2880
48 33.6 2.40 84.9 7680

Coil

Coil Power Standard Type:500mW ~ 590mW
Sensitive Type:150mW ~ 300mW

Safety Approval Ratings

UL&CUL 2A/30VDC,
0.6A/125VAC

Outline Dimensions, Wiring Diagram And PC Board Layout Unit: inch(mm)

Outline Dimensions
cas 3 1
Wiring Diagram
(Bottom view)
cas 4 1
PCB Layout
(Bottom view)
cas 5 1

Remark:
1) In case of no tolerance shown in outline dimension: outline dimension ≤1mm,tolerance should be ±0.2mm; outline dimension >1mm and ≤5mm,tolerance should be ±0.3mm;outline dimension >5mm, tolerance should be ±0.4mm.
2) The tolerance without indicating for PCB layout is always ±0.1mm.

Characteristic Curves

cas 6 1
cas 7 1
cas 8
Addcom Solution Pte Ltd